Industrial Servo Motor Mini Lathe Milling Machine Speed Control Switch Sewing

Description

These Custom built rotary speed control switch's replace the pedal switch found on most industrial sewing servo motor controllers.
They are not intended for use on industrial sewing machines.
See pictures.
Designed
specifically
for our (The Custom Crafter) Servo motors and
Controllers
.
They are built for those of us using these servo motors to modify our old or inferior machines.
Additionally they will work with recent model Vevor or Mophorn industrial servo motor and who want a better looking speed control system.
Tested and proven on the above brands and may work on other brands that have the lever style switch.
Plug and play, just turn off the system, unplug the lever switch and plug this one in it's place.
Only Fits and works with:
The Custom Crafter servo motors
2021 and newer Vevor brand with identical control unit as seen in images.
2021 and newer Mophorn brand with identical control unit as seen in images.
Your control unit PCB must look identical to the one in the photos above or this will not work.
Tested and proven on motors built and sold under The Custom Crafter Brand.
Does not fit or work with:
Sewtco Industrial Sewing Machine Servo Motors.
Eagle 750 Sewing Machine motors.
Consew systems.
No returns item, purchase at your own risk when using on other brands!
Will not cause fault codes.
When you turn on the
controller
it will go through self
prognostics
and set at zero ready to go.
Safety feature
(does not apply on remote capable switch):
If you inadvertently turn on the power with the speed control set to any speed besides stop; The motor will not run until your turn the rotary to full stop. Than self diagnostics will complete and you are ready to go.
Switch active function:
See images for estimated speeds at selected positions.
Make Note: RPM locations on switch may not match actual speeds achieved your system:
RPM locations are based on
programming set at min 300~max 4,500
.
If you change the
programming
, the RPM positions will also change but not on the switch.
Tests with the 750 watt motor
have revealed as follows:
Position on switch 300 on display 300
Position on switch 600 on display 900
Position on switch 2,000 on display 2,300
Position on switch 4,500 on display 4,500
This will require a different label to match but there is no reason to run a print
due to the fact there is a new switch in R&D right now. Completion is 6 months
out so use this switch if you need it now.
Tests with the 900 watt motor:
The 3,500 RPM switch was originally designed for the 1,000 watt motor.
It is fairly accurate with the 900 (within 100 RPM).
Tests with the 1,000 watt motor are pending
.
See 900 for now.
T
ests with the 1,500 watt motor
have revealed as follows:
Position on switch 300 on display 300
Position on switch 600 on display 1,100
Position on switch 2,000 on display 2,300
Position on switch 3,500 on display 3,500
This will require a different label to match but there is no reason to run a print
due to the fact there is a new switch in R&D right now. Completion is 6 months
out so use this switch if you need it now.
These switches are now at prototype 8 or higher and still in development.
Therefore
we will not issue refunds, returns or exchanges simply because the
numbers on the switch do not match the actual motor speed.
We reserve the right to cancel the purchase and refund your money
If/when you order/buy a one of these switch's without advance
communication
Custom built switches require advance
communication
prior to purchase.
90 day limited warranty
:
If this switch fails, return it and I will replace it or refund your purchase as follows:
Buyer pays return shipping.
We will inspect and test it and if it is defective and there is no obvious physical/electrical damage,
we will ship you a replacement.
Physical damage is cut wires, pried or attempted to open housing.
Electrical damage is, buyer let the smoke out do to improper use such as, attempting to install it on something besides
a Custom Crafter Control Unit in the images or incorrect voltage was applied by outside influences such as voltage spikes caused by lightening or some how plugging it directly into a 110 volt outlet instead of the control unit.
Solid state:
No user serviceable parts inside.
Glued assembly is impossible to open without major damage.
For that reason, if it fails (see warranty), return it. I will send a replacement or refund your purchase.
Reverse engineering:
Do not waste your time and money.
Instead: Contact me and
discuss
your project. I will then make an eBay offer for you to buy the parts required.
Shipping:
Ships USPS ground.
Returns:
Buyer pays return shipping.
Ask lots of questions:
Do not purchase under pressure. I am constantly building more. There are
improvements
in R&D
right now. When these improvements are proven, all new switches include that
improvement
.
Thank you for looking.